- Location
- Forums
- Miscellaneous Aquarium Discussion
- Coiffe IT Yourself (DIY)
You should ascent or purpose an alternative browser.
How to exchange computer fans to forg with average plug
- Thread starter Mombo
- Start date
- Labelled users None
- #1
- Linked
- English hawthorn 2, 2022
- Messages
- 593
- Reaction score
- 248
- Brushup sexual conquest
- +0 /0 /-0
Information technology seems like I accept seen quite few people victimisation fans like this.
How are yall devising it study with the normal plugs you have available to you round a marine museum?
- #2
- Thread Starter
- #3
- Joined
- May 2, 2022
- Messages
- 593
- Reaction score
- 248
- Reexamine tally
- +0 /0 /-0
- #4
1. When you cut that conclusion plug, one wire will be positive, the new negative. You need to hook up the positive wire to the positive side of the rooter. If you don't, the fan will run rearwards.
2. Amps are additive. If you are hooking up multiple fans, you need to add up the amp valuation happening each fan, and this numerate can't exceed the amp rating of the power render....with the one you've shown, 3 amps.
- #5
This is the one I use happening my two 120mm instance fans in my canopy.
- Thread Starter
- #6
- Joined
- May 2, 2022
- Messages
- 593
- Response score
- 248
- Review score
- +0 /0 /-0
- #7
- Direct the fans so they tout onto the water/into the stand rather than the other way around. The humidness and salt nebulizer are vitriolic and will wreck the ball bearings quickly if you use the fans A exhaust fans.
- Think of upkee - make the fans well-founded easy to replace for when they do wear down (they will,) and consider adding a barrel jack connector to them to cook it easier to disconnect them if IT should be necessary.
- Earnings care to make noise and airflow when you buy- any fans are overmuch quieter than others and some blow a lot more air than others.
If you have an Apex 2022, the DC24 outlets on the EB832 buns directly power a 24v fan as semipermanent As it's to a lesser degree 30 W
- #8
- Connected
- Feb 25, 2014
- Messages
- 28,741
- Response score
- 40,839
- Refresh score
- +0 /0 /-0
- Location
- Calif.
- #9
- Joined
- Dec 8, 2013
- Messages
- 1,093
- Chemical reaction score
- 548
- Review score
- +0 /0 /-0
- Location
- Florida
- Wander Starter
- #10
- Joined
- May 2, 2022
- Messages
- 593
- Reaction score
- 248
- Review score
- +0 /0 /-0
Good note on the sustentation part. I was planning on just screwing information technology into the suffer but after doing that 3 or 4 multiplication they might be a bit worn proscribed. Need to think of an alternative for that possibly....
- #11
AC Infinity AXIAL 8038, Muffin Cooling Winnow, 115V AC 80mm by 80mm by 38mm Blue Pep pill
or
Tjernlund 8710001 High Speed Gem Winnow with Chilling Mechanism, 110 CFM, 120 mm x 120 mm x 38 mm, 110V AC from Amazon
- #12
I give mine screwed into the overcompensate for my overflow, blowing down onto the water equally it comes over the weir. Information technology's an acrylic cover, so I just drilled a rounded hole for the fan and 4 holes at the corners then picked up some stainless bolts with a couple neoprene washers for vibration closing off at my local hardware store.I like the design of the new style fans haha otherwise no reason I guess.Good banker's bill connected the maintenance part. I was provision on simply screwing it into the stand but aft doing that 3 or 4 times they might be a bit worn out. Motive to mean of an alternative for that maybe....
You arse for certain employment screws, too. If/when the holes wear away just practice session them through with and use bolts.
- #13
- Joined
- May 3, 2022
- Messages
- 495
- Chemical reaction score
- 703
- Review score
- +0 /0 /-0
- Location
- NOCO
- #14
I utilized these atomic number 3 well, for all 12 v D.C. requirements (moonlight, kessil controller, dosers, fans [part of temperature controller]). I would repeat the assonant advice distributed earlier, check the amp evaluation with your fan's consumption, and check for UL enrolled products only when.I used these adapters to wire up cpu fans for my equipment console to dungeon my MH ballasts cool. They exercise great. I have them assault a timer to run only if the MH's are on.
https://World Wide Web.virago.com/gp/product/B00FEOB4EI/ref=oh_aui_detailpage_o06_s00?Internet Explorer=UTF8&psc=1
Information technology is trivial to control their speed as well , i.e you can actually build Oregon down the speed of the fans based on certain conditions.
- #15
MSB123
Someone out there put something smart here.
- Review score
- +0 /0 /-0
- #16
I use pigtails look-alike these to connect office supplies to fans and such.
https://www.virago.com/JacobsParts-...7760288&ere;sr=8-11&keywords=2.1mm+female+adapter
I besides like to spend a couple of bucks more and get IP65 Beaver State higher fans.
Bruce
- #17
- Joined
- May 6, 2022
- Messages
- 531
- Reaction score
- 281
- Review score
- +0 /0 /-0
- #18
- Joined
- Sep 26, 2022
- Messages
- 119
- Reaction score
- 79
- Review score
- +0 /0 /-0
- #19
- Joined
- May 6, 2022
- Messages
- 531
- Reaction score
- 281
- Review tally
- +0 /0 /-0
- Thread Appetiser
- #20
- Joined
- English hawthorn 2, 2022
- Messages
- 593
- Reaction hit
- 248
- Review score
- +0 /0 /-0
Corresponding duds
- Home
- Forums
- General Fish tank Discussion
- Do It Yourself (DIY)
Source: https://www.reef2reef.com/threads/how-to-convert-computer-fans-to-work-with-normal-plug.329595/
0 Comments